For use in Class I Division 2 Groups A, B, C and D hazardous locations, the Iron Cross Emergency Lighting Series is designed to prevent ignition of hazardous materials in locations where flammable materials are stored and handled.

• Each unit comes with two (2) weather - resistant, impact - resistant, flame - retardant thermoplastic EF - 11 lamp heads with 12 watt high intensity sealed beam tungsten lamps (standard).
• Temperature code: T4A (max. 120 degrees C).
• Water - and corrosion - resistant cabinet is made of fiberglassreinforced polyester. Industrial gray cabinet is fully gasketed around the cover. Battery compartment is vented with a breather vent designed to permit exhaust of battery gases without admitting external moisture or corrosives.
• Available with sealed, maintenance - free Lead - Calcium batteries.
• Fully automatic pulse charger offers 120/277 Vac, 60 Hz., 0.43/0.2 Amp., limited current temperature compensation, short circuit proof, reverse polarity protected, low voltage battery disconnect, brownout protection and standard solid state transfer feature.
• PAR36 sealed - beam halogen lamps
• Standard Self - Diagnostic circuitry continuously monitors every critical function of the unit. If a problem occurs, a single fault indicator on the outside of the fixture flashes immediately. A detailed diagnostic display is located internally. The detailed display will further indicate the nature of the fault as either a battery fault, load fault or a charger fault.
• UL Listed. Complies with NEC, Life Safety Code and OSHA. The test switch and AC pilot light are explosion proof in design and exceed requirements for Class I, Division 2, GroupA, B, C & D.
• 3 - year full warranty, excluding lamps, pilot lights and fuses.

The ICIL Series has a 3 - year full warranty. The water and corrosion resistant cabinet is formed from injection molded structural foam, glass reinforced material. The cabinet is fully gasketed around the cover. The test switch and AC pilot light are designed and exceed requirements for Class I, Division 2, Group A, B, C & D. The battery compartment is vented with a breather vent designed to permit exhaust of battery gases without admitting external moisture or corrosives. This design is also suitable for use in Class II Division 2, Group F & G applications. The ICIL Series has a industrial gray finish and two EF11 weather resistant thermoplastic heads each with a 12 watt sealed beam high intensity tungsten lamp mounted on top of the enclosure. The 1 inch conduit entry has a rubber cover to eliminate all exposed metal parts.

A Fully automatic pulse charger offers 120/277 VAC 60 Hz., 0.43/0.2 Amp., limited current temperature compensation, short circuit proof, reverse polarity protected, low voltage battery disconnect and brownout protection.

Diagnostics circuity continuously monitors every critical function of the unit. If a problem occurs, a single fault indicator on the outside of the fixture flashes immediately. A detailed diagnostic display is located internally. The detailed display will further indicate the nature of the fault as either a battery fault, load fault or a charger fault.

The Iron Cross Emergency Lighting system is available in 6 or 12 volt emergency lighting and is designed to be installed in accordance with Article 501 of the National Electrical Code and is UL Listed. The transformer is 120/277 volt. Units are furnished with sealed 6 or 12 volt battery. The unit charger utilizes a micro - controller circuit which samples the battery in relation to its temperature, state of charge and input voltage fluctuations. The charger is current limited, temperature compensated, short - circuit proof and reverse polarity protected. The unit is furnished with an electronic lockout circuit which will connect the battery when the AC circuit is activated, and an electronic brownout circuit which will activate the unit when utility power dips below 80 - 85% of nominal voltage. A low voltage battery protection circuit is provided and will disconnect the load and circuitry from the output circuit when battery reaches 87 - 1/2% discharge. The unit is furnished with one or two protected charger output circuits and a solid state switch. The unit is capable of full recharge in compliance with Underwriters Laboratories specifications.

The unit is furnished complete with a test switch and AC pilot light UL Listed for Class I Division 2 requirements. Cabinet is constructed of Injected molded structural foam, glass reinforced. The unit has a fully gasketed cover. The battery compartment is provided with a breather vent designed for Class I Division 2 operation. The unit is furnished with two EF 11 weather resistant lighting heads. Heads are constructed of impact resistant, flame retardant thermoplastic complete with 12 watt sealed beam high intensity lamps.

Stahlin Vapor Capsules contain a unique vapor phase inhibitor designed to protect metallic surfaces within an enclosure against airborne corrosion. By simply placing these self - contained capsules inside an enclosure the vapors readily permeate every point, passivating all metallic surfaces. When the capsule is removed from its sealed package, it begins to emit an invisible, non - toxic vapor which is diffused throughout the surrounding atmosphere until the air is saturated. The vapor then passivates the metal surfaces against atmospheric corrosion by reducing the electro - chemical activity of the metal surfaces. Radius of Protection is 2 ft with a normal life span of 1 year.

Enclosure

Structural foam, glass reinforced construction.

Finish

Industrial gray

Servicing

Fully gasketed front provides access to battery and charger.

Lighting Heads

The unit as standard, is furnished with two, EF11 weather resistant thermoplastic heads utilizing 12 watt sealed beam lamps.

Face Colors

Housing Colors

Mounting Ability

Housing Material

Temperature Rating

Power Input

120/277 Vac, 60 Hz., 0.43/0.2 Amp.

Power Output

6 or 12 volt protected output circuit. 24 watts or 56 watts

Transfer

Automatically and instantly energizes lamp load upon failure of AC supply.

LVD

Low voltage battery disconnect circuit automatically shuts down lamp load and circuitry when battery reaches 87 - 1/2% discharge, preventing deep discharge and permanent damage to the battery.

Brownout

Close tolerance electronic circuit activates emergency unit when utility power dips below 80 - 85% of nominal voltage.

Charger

The pulse plus charger circuit utilizes a microcontroller which samples the battery in relation to its temperature, state of charge and input voltage fluctuations. The charger is current limited, temperature compensated short - circuit proof and reverse polarity protected. Charge regulation +/ - 1%. The equipment is capable of full recharge in compliance with UL 924 specifications.

Transformer

120/277 VAC

Controls

Sealed push - to - test switch, indicator light for ACOn and fault indicator (flashes).

Applications

• Manufacturing Plants
• Chemical Plants
• Food Processing Areas
• Paint Shops
• Moisture, Dirt or Dust Concerns
• Wet or Corrosive Conditions
• UL Listed

Illumination Source

PAR36 sealed - beam halogen lamps. Available in: 6V 8W, 6V 12W, 12V 8W, 12V 12W

Battery Type

Sealed Lead Calcium

Performance Testing

Sealed push - to - test switch, indicator light for AC - On and fault indicator (flashes).

Maintenance

Battery is maintenance free. Diagnostic circuitry continuously monitors every critical function of the unit. If a problem occurs, a single fault indicator on the outside of the fixture flashes immediately. A detailed diagnostic display is located internally. The detailed display will further indicate the nature of the fault as either a battery fault, load fault or a charger fault. Fully gasketed front provides access to battery and charger.

Unit is designed to be back mounted to wall surface via 4 fasteners.

Mounting

Back mounted wall surface

Electrical Connections

1. The unit is to be installed with wiring methods in accordance with the requirements of NEC Article, 500 and 501.
2. Turn off AC power.
3. Route AC circuit wires to electrical box and leave 12 inches of wire length.
4. Remove four screw on door. Open door by lifting it away from housing.
5. Securely mount unit in place. Connect AC supply wiring to unit as follows For 120 VAC operation - Black to 120 VAC, white to neutral. Insulate unused wire. For 277 VAC operation - Orange to 277 VAC, white to neutral. Insulate unused wire.
6. Extend DC wiring for remote fixtures (if required) to unit. Wiring must comply with NEC articles 700, 720 and 501 - 4. Do not exceed rated wattage of unit, integral and remote lampheads combined.
7. Connect two white lamp wires to black wires from circuit board with wirenuts provided. Note: lamp wires are not polarized.
8. When ready to energize AC, connect batteries by plugging the red leads into the positive terminals and the blue leads into the negative terminals. Lamps will not light at this time.
9. Energize AC. Allow unit to charge for 24 hours before initial testing.

Internal Battery Heater

This option is used in areas where temperature may drop below 0 degrees C. The thermostat will activate the heating pad at 0 degrees C and will cut at 16 degrees C. The heating pad is rated at 50 watts.

Time Delay

This option is used in areas where metal halide or mercury vapor lights are present, or lighting systems that lapse before startup. Intervals available are: 5, 10, or 15 minutes

Shatter resistant teflon coated lens

Wire Guard is available

• Manufacturing Plants
• Chemical Plants
• Food Processing Areas
• Paint Shops
• Moisture, Dirt or Dust Concerns
• Wet or Corrosive Conditions

UL Listed - Class I Div 2 Groups A,B,C,D and Class II Div 2 F and G

Entire unit (excluding lamps and fuses) carries a 3 - year Full Warranty. The battery has 8 - year life expectancy, 3 - year Full Warranty, plus 3 - year pro rata warranty